This is an amazing piece of work by Denis, “The Teenage Woodworker”. Check it out!

This desk is my pride and joy! It’s a serpentine Bow Front writing desk that I built over the summer out of a giant slab of 10/4 x 13” x 9’ ribboned Sapele. That being said the fact that it is built out of one slab is very crucial to this desk. Since it was all on board all of the color as well as the grain matches all over the desk. Examples of this are the top which is book matched out of two pieces as well as the front apron which is a bent lamination with the drawers cut out of the front to maintain the grain flow through the front. The drawers themselves are constructed with hand-cut dovetails. It was difficult to cut them on the curved surface both because of the curve and trying to handle the front to chop out the pins but I got through. It only took about 10 tries to get the front dovetails to look perfect lol. When it came time for finish it was a simple Sherwin Williams pre-cat lacquer. About 4 full coats in total and then rubbed out with a paper bag to get it super smooth. The lacquer really makes this ribboned Sapele shine but not so much that the figure outweighs the curves of the desk. In the end I had a really great time building this project and it is my favorite so far. Now onto the slant front desk!!

Denis is actually trying to sell this piece so that he can purchase wood for his next project. So if you know anyone who might be interested in purchasing it, send me an email and I can connect you with Denis.

This Viewer Project post is a two-fer. Gerald sent us pics of a beautiful chest of drawers as well as a doll desk for his daughter. Check it out:

The Chest of Drawers

My wife’s sister asked that I build her son a chest of drawers similar to one that she had seen in a furniture store near her house. It was a painted item of poor quality. This would be my first opportunity to design and create a piece from start to finish.

I started with the overall dimensions and began creating the shop drawings for the piece. I am a Professional Land Surveyor by trade so I was able to utilize Autocad for the drawings. I went through every piece in my home to get different ideas on how to design the case for the piece. The design I ended up using seems pretty simple once I broke it down into the components. The sides are a frame and panel between the two legs. The supports for the drawers are a simple frame design and really worked well. The top is an edge glued panel of the best stock I had on hand.

The drawers are constructed using a type of locking rabbet joint in front and dado in the rear. As can be seen on the photos I reinforced all interior corners with small mitered pieces just to add more strength to the joints. This piece is going to a small child and I wanted to be sure he could not pull the drawers apart. The drawer slides are full extension glides. A little unusual for a furniture piece but again I wanted to make sure that if he was to lean down on the drawers or to climb on them that they would support the load and not give way.

The drawer fronts for the top three drawers and the middle two were cut from one piece of stock to insure grain continuity across the piece. Really makes the piece stand out when completed. All joinery on this project are Domino’s from Festool. Thanks again to Dennis Kent of Woodcraft for suggesting this tool for my shop. It is an awesome tool that makes quick, strong and accurate joinery.

The finish was lots of fun to watch come together. The cherry really comes to life during the finishing process. I started by sealing the raw cherry with a wash coat of shellac to help control blotching. This was followed by two coats of Minwax “Cherrywood” gel stain. The gel stain was easy to work with and ended up being very transparent. It really allowed the grain to show through on the completed project. The second coat was when the character of the cherry began to show. The top coat is lacquer sprayed on with my Earlex HVLP system. Multiple coats were applied to allow wet sanding and hand polishing up to the desired sheen. I think the top came out nicely once the sanding and polishing were completed. Antique brass hardware completed the look and matched nicely with the cherry.

The Doll Desk

My daughter Sarah has several American Girl dolls and loves to play school with them. She asked daddy for a desk for “Julie” and I set out to see what I could come up with.

This project was built pretty much on the fly. Sarah had seen an old type desk at our church and wanted Julie’s to be like it. I decided that since I had some nice Red Oak left from from another project I would use it. The desk compartment is a simple box with a slant top that opens to storage below. A pencil groove was routed in the flat area near the top. Corners are simple rabbets and the bottom is tempered hard board floating in a groove milled into the sides.

The chair is sized to fit Julie and utilized some thin stock that was left over from another project where I had resawn some oak for another use. The sides utilize a half lap joint and are surprisingly strong. The seat and back stretchers are the thin resawn stack that I mentioned earlier. The chair support and desk support is again built from some scrap pieces I had around the shop from larger pieces. The original thought was to have the vertical support for the desk and chair be the only pieces under each. Once the pieces were assembled it became obvious that more support was needed laterally to prevent each from racking. I added the mitered braces to help with the flex of the thin stock. I finished the piece with two coats of satin polyurethane.

Now Sarah and Julie can play school in style!

This week’s project is submitted by Chris. Let’s check it out and see what he has to say:

“I’ve been watching your videos for the last few months, and find them very enjoyable. I watched Part 1 of the gadget station last night, and what you’re working on is very much like a project I built for myself earlier in the spring.”

“Back in the old days, Stickley built a desk called the #706. It’s a small secretary-type desk, and the top of it is basically a gadget station with a drop down door for a laptop (like your first station, but this one has a better way for supporting the door). For somebody who wants a gadget station but also needs a small desk for a laptop, it’s perfect. That’s what I use mine for.”

“The desk itself was built entirely with hand tools…vintage panel and back saws, hand planes (most vintage, but a few new Lie-Nielsen and Veritas planes), and chisels (short chisels are Ashley Isles, long chisels are mostly vintage). The top and bottom shelf are attached to the sides using hand cut wedged through-mortises. The back is ship lapped pine boards. The door utilized haunched mortise-and-tenon joinery with floating solid panels. I will admit to using a random orbit sander to get the inside of the door perfectly level though, but I did get it pretty close with just hand planes. :) I finished the desk with shellac….something like 18 coats padded on.”

“It’s built with clear pine…I’m a total hand tool person so quartersawn oak was not going to happen (original Stickleys in QS oak looks AMAZING though). One pic is when it was brand new and one is with the adjustable shelving system I built for it. Devices that need charging sit in the middle (iPod, cellphone, etc.), and the side shelving is wide enough to accommodate CD/DVD storage. When not in use, the laptop stands on edge and leans back against the shelves….it tilts backwards slightly so it won’t fall out.”

“You’ll see that the door’s pivot location is about 1/4 from the bottom, so the shelf in the desk actually supports the door when it’s open (better than using mechanical supports). Overall, I’m really happy with it….maybe somebody else watching the videos might find the design to their liking as well, or maybe this will give you a little inspiration or something.”